久久精品国产99久久香蕉_濟南雕刻機的主軸電機是水冷的好還是風冷的好?_業內資訊_新聞中心_保麗龍雕刻機_五軸_四軸

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

業內資訊

濟南雕刻機的主軸電機是水冷的好還是風冷的好?

來源：http://m.oicv.cn 時間：2021-06-02

濟南雕刻機的主軸電機是水冷的好還是風冷的好?對于這個問題，很多客戶都有疑問，在這個問題上，我們簡單介紹一下：來認識一下兩者的共同點：在內部結構來說，二者是統一的，都是采用定子繞線圈轉動;從電機的控制方式來說，水冷的幾乎都是變頻控制的，風冷主軸則不然，可以采用變頻和不變頻的方式控制。水冷主軸和風冷主軸的區別：

Jinan engraving machine spindle motor is water-cooled or air-cooled good? For this problem, many customers have doubts. On this issue, let's give a brief introduction: first, let's understand the common points of the two: in terms of internal structure, the two are unified, and both use the stator to rotate around the coil; From the control mode of the motor, the water-cooled spindle is almost controlled by frequency conversion, but the air-cooled spindle is not. It can be controlled by frequency conversion or non frequency conversion. Difference between water-cooled spindle and air-cooled spindle:

一、水冷顧名思義就是采用水循環來冷卻主軸高速旋轉后產生的熱量，這樣的效果就會(huì )很好，因為水經過流通之后的溫度(常用測試)不會(huì )超過40度;風冷的主軸采用風扇的方式來散熱，其效果肯定不如水冷;

1、 Water cooling, as the name suggests, is to use water circulation to cool the heat generated by the high-speed rotation of the spindle, so the effect will be very good, because the temperature of water after circulation (commonly used test) will not exceed 40 degrees; The air-cooled spindle uses fan to dissipate heat, and its effect is certainly not as good as water cooling;

二、噪音，水冷的主軸基本上沒有噪音，但是風冷的主軸則很響;

2、 Noise, water-cooled spindle basically no noise, but the air-cooled spindle is very loud;

三、使用壽命，水冷主軸要注意保養、勤換水或者采用工業水冷卻機，這樣的主軸壽命要比風冷主軸長很多!

3、 Service life, water-cooled spindle should pay attention to maintenance, frequently change water or use industrial water cooler, such spindle life is much longer than air-cooled spindle!

四、精度，水冷主軸軸向、徑向跳動基本上都是在0.003毫米以下，而風冷主軸(國產)則遠遠不及。

4、 Accuracy, axial and radial runout of water-cooled spindle are basically below 0.003 mm, while air-cooled spindle (made in China) is far less than.

以上就是小編為大家介紹的關于雕刻機的相關內容，希望可以幫助到大家。更多精彩內容可以直接關注：http://m.oicv.cn

The above is Xiaobian for you to introduce the relevant content of engraving machine, hope to help you. More highlights can be directly focused on: http://m.oicv.cn