亚洲国产欧美国产综合一区_雕刻機的干擾問題怎么解決？_業內資訊_新聞中心_保麗龍雕刻機_五軸_四軸

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

業內資訊

雕刻機的干擾問題怎么解決？

來源：http://m.oicv.cn 時間：2021-06-17

經過我們的技術團隊分析，發現是由于一般步進電機和驅動器外殼未采用鋁、鈦、鎂合金外殼進行磁屏蔽，對高靈敏的接收機系統造成干擾，使其無法工作，并且污染電源，造成雕刻機控制系統的單片機和上位機無法進行通訊，嚴重者造成單片機死機，給正常使用造成了困難，因此干擾問題必須加以解決。

Through the analysis of our technical team, we found that the general stepper motor and driver Shell did not use aluminum, titanium, magnesium alloy shell for magnetic shielding, which caused interference to the highly sensitive receiver system, made it unable to work, and polluted the power supply, resulting in the engraving machine control system's single-chip microcomputer and upper computer unable to communicate, and even caused the single-chip microcomputer crash, It is difficult for normal use, so the interference problem must be solved.

一、加裝電源濾波器，減少對交流電源的污染。

1、 Add power filter to reduce the pollution of AC power supply.

將電源濾波器的地、驅動器PE（驅動器與機箱底板絕緣）、控制脈沖PULSE-方向脈沖DIR-短接后的引出線、電機接地線、驅動器與電機之間電纜防護套、驅動器屏蔽線均接到機箱壁上的接地柱上，要求接觸良好。

Connect the ground of power filter, PE of driver (insulation between driver and chassis bottom plate), outgoing line of control pulse direction pulse dir short circuit, motor ground wire, cable protective sleeve between driver and motor, driver shield wire to the grounding post on chassis wall, and ensure good contact.

二、盡量加大控制線與電源線（L、N）、電機驅動線（U、V、W）之間的距離，避免交叉.比如我們在處理雙軸驅動系統中兩個處在同一機箱的驅動器安裝位置時,木工雕刻機一個驅動器銘牌朝前，另一個則朝后，并在結構布置上使這些引線盡量短。

2、 Try to increase the distance between the control line and the power line (L, n), motor drive line (U, V, w) to avoid crossing. For example, when we deal with the installation position of two drivers in the same chassis in the dual axis drive system, one driver's name plate of woodworking engraving machine is facing forward, the other is facing backward, and these leads should be as short as possible in the structural arrangement.

三、使用屏蔽線減輕外界對自己的干擾，或自己（電源線）對外界的干擾。

3、 Use the shielded wire to reduce the interference from the outside world, or from the outside world.

更多石材雕刻機整機和石材雕刻機配件和配套服務，請關注我們石材雕刻機廠家官網了解。

More stone carving machine and stone carving machine accessories and supporting services, please pay attention to our official website of stone carving machine manufacturers.